Ancient and Early Ships

Viking Longships: Design, Construction and How They Sailed

How Viking longships were built: shell-first oak planking, iron rivets and caulking, the side steering oar, and how these ships sailed with sail and oar.

On this page
  1. What made a longship a longship
  2. How they were built, step by step
  3. How they sailed
  4. Navigation at sea
  5. Surviving ships
  6. Modern replicas
  7. Frequently asked questions

Short answer: Viking longships were built shell-first, from overlapping oak planks joined with iron rivets and sealed with wool and tar, with a framework added afterwards. The result was a long, shallow-draft hull that could be sailed or rowed and could move on open sea and up rivers.

What made a longship a longship

The name “longship” describes a warship or long-distance vessel with a long, narrow hull. These ships were much longer than they were wide, and their shallow draft let them run into shallow rivers and beach on gravel shores. The hull was often symmetrical at the bow and stern, which made it easy to change direction without turning the ship around.

Longships carried a crew who both rowed and sailed. Oars gave control in calm weather and near shore, while a sail provided power on longer passages with a favourable wind.

How they were built, step by step

The construction process is well understood from surviving ships, reconstructions and experimental archaeology. The main steps were:

  1. Timber selection and splitting. Shipwrights chose trees with suitable shapes. They split logs into planks along the grain, using wedges and axes, rather than sawing them. Splitting kept the wood fibres intact, which made the planks strong and flexible.
  2. Keel and stem. The keel was a long, carefully shaped timber that formed the backbone of the ship. The stem and stern pieces were fixed to its ends, and decorative carvings sometimes finished the upper ends.
  3. Shell-first planking. The outer hull was built from the bottom up, with each plank overlapping the one below, like roof tiles. This is called clinker or lapstrake construction.
  4. Riveting. Overlapping planks were fastened with iron rivets, and small square washers called roves were fitted on the inside. The joints gave the hull flexibility, so it could move with the waves instead of breaking.
  5. Caulking. The seams were sealed with wool or animal hair pushed into the gaps, and then covered with tar or a similar sealant.
  6. Frames and fittings. Only after the outer shell was complete were the inner ribs, floor timbers and cross-beams fitted. These locked the hull’s shape in place.
  7. Mast, sail and steering oar. A single mast was stepped into the centre of the ship, and a large square sail was hung from a yard. A steering oar was fixed to the right-hand side of the stern. The word “starboard” comes from this steering side.

Building a longship was a substantial job, and it required skilled shipwrights and good timber. The exact time needed is not well documented, and estimates vary.

How they sailed

Longships could sail with the wind, using their square sail, or be rowed with oars when the wind was weak or contrary. Oars were arranged in rows along the hull, and the number varied by ship. A crew could row in shallow water, in calm conditions or when moving into an attack, while the sail carried the ship on longer passages.

The shallow draft let longships run up rivers and onto beaches. This gave Viking crews access to targets that deeper ships could not reach. It also made the ships useful for trade, since they could carry goods to coastal and riverside markets.

Viking navigation is less well documented than their ship design. Most historians think they used the sun’s position, the stars, landmarks, coastal features, bird behaviour and the feel of the sea and the wind. Some sources mention a “sun stone” that might have helped locate the sun on cloudy days. How this worked in practice is debated, and it should not be treated as a settled fact.

Surviving ships

Several longships survive from the Viking Age and the period just after. The Gokstad ship, found in Norway in 1880, is about 23 metres long and dates to around 900 CE. It is displayed in the Viking Ship Museum in Oslo. The Oseberg ship, also from Norway and in the same museum, is an earlier and more richly decorated vessel that was used in a burial. Five ships found sunk in Roskilde Fjord in Denmark, known as the Skuldelev ships, show a range of Viking-era designs, including cargo ships and warships.

Surviving ships are often fragments or reconstructions, so they must be interpreted carefully. Their shapes and rivet patterns are the best evidence for how the longships were built.

Modern replicas

Several replicas of Viking ships have been built and sailed. They help test how the ships handled, how they were rigged and how long they took to build. The Sea Stallion from Glendalough, a replica of the Viking-era Skuldelev-type ships, sailed from Ireland to Denmark in 2007. Replicas can show what a longship could do, but they cannot prove every detail of the original design.

Frequently asked questions

Were longships different from knarrs?

Yes. The longship was built for speed and manoeuvrability, with a long, narrow hull and oars. The knarr was a broader, deeper cargo vessel, designed to carry goods more than to fight or race.

How long did a longship take to build?

There is no reliable figure. Estimates depend on the ship’s size, the availability of timber and the skill of the builders. It was a major project that could take many months.

For the wider history of sailing ships, see our history of sailing ships. For another Northern European ship burial, see our article on the Sutton Hoo ship burial.

The complete guide to ancient and early ships

History of Sailing Ships: A Timeline from the First Boats to the Age of Sail
Read the guide

Keep exploring

Guides from other topics

All topics →